first commit USB MIDI Host2Host

USB_MIDI_Host2Host/USBMIDIHost2Host_QTPyRP2040.ino

@@ -0,0 +1,163 @@
+// SPDX-FileCopyrightText: 2025 John Park and Tod Kurt
+//
+// SPDX-License-Identifier: MIT
+
+// Use a DMX controller to drive NeoPixel strips
+// Arduino Uno or Metro 328 + Conceptinetics DMX Shield
+// Recieves incoming DMX messages from controller, translates to NeoPixel
+
+// MIDIHost2Host -- Connect two USB-MIDI host devices together
+// 2019 @todbot / Tod E. Kurt
+// 2025 @johnedgarpark / John E. Park
+ // This sketch is meant to be installed on two Adafruit QT Py RP2040s.
+// The connections between the two QT Py RP2040s are
+// QTPyA Gnd ----- QTPyB Gnd
+// QTPyA TX  ----- QTPyB RX
+// QTPyA RX  ----- QTPyB TX
+// except it's done w PIO over the stemma qt cable (remove red wire first)
+
+
+//  When compiling:
+// Install libraries: Adafruit_TinyUSB & MIDI
+// Be sure to have updated all boards and libraries
+// Select "Tools" -> "USB Stack" -> "TinyUSB"
+
+// The following libraries are required:
+// Adafruit_TinyUSB library by Adafruit
+// https://github.com/adafruit/Adafruit_TinyUSB_Arduino
+// MIDI Library by Forty Seven Effects
+// https://github.com/FortySevenEffects/arduino_midi_library
+
+
+#include <Arduino.h>
+#include <Adafruit_TinyUSB.h>
+#include <MIDI.h>
+#include <Adafruit_NeoPixel.h>
+
+// Adjust these for flashing the two different boards either "red" or "blue"
+#define RED_BOARD  
+// #define BLUE_BOARD
+
+
+
+// Color definitions
+uint32_t RED = 0xCC0000;
+uint32_t DIM_RED = 0x3F0000;  // 25% brightness red
+uint32_t GREEN = 0x00DD00;
+uint32_t BLUE = 0x0000CC;
+uint32_t DIM_BLUE = 0x00003F;  // 25% brightness blue
+uint32_t YELLOW = 0xAAAA00;
+char mfgstr[32] = "Lars Productions";
+#ifdef RED_BOARD
+  char prodstr[32] = "QTHost2 Red";
+  uint32_t LED_COLOR = RED;  
+  uint32_t LED_DIM_COLOR = DIM_RED;  
+  SerialPIO pioserial(23, 22);
+#else
+  char prodstr[32] = "QTHost2 Blue";
+  uint32_t LED_COLOR = BLUE;
+  uint32_t LED_DIM_COLOR = DIM_BLUE;
+  SerialPIO pioserial(22, 23);
+#endif
+
+
+// NeoPixel settings
+#define NUM_PIXELS 1
+
+// NeoPixel RGB LED
+Adafruit_NeoPixel pixels = Adafruit_NeoPixel(NUM_PIXELS, PIN_NEOPIXEL, NEO_GRB + NEO_KHZ800);
+
+bool led_on = false;
+uint32_t led_time;
+uint32_t led_on_time = 50; // how long LED should blink
+uint32_t last_color = LED_DIM_COLOR; // Track last active color
+
+// USB MIDI object
+Adafruit_USBD_MIDI usb_midi;
+
+// Create instance of Arduino MIDI library,
+// and attach usb_midi as the transport.
+// MIDI_CREATE_INSTANCE(Adafruit_USBD_MIDI, usb_midi, midiA);
+MIDI_CREATE_INSTANCE(Adafruit_USBD_MIDI, usb_midi, midiA);
+
+// Create instance of Arduino MIDI library,
+// and attach HardwareSerial Serial1 (TrinketM0 pins 3 & 4 or TX/RX on a QT Py, this is automatic)
+MIDI_CREATE_INSTANCE(HardwareSerial, pioserial, midiB);
+
+
+void setup()
+{
+
+
+  #if defined(NEOPIXEL_POWER)
+    // If this board has a power control pin, we must set it to output and high
+    // in order to enable the NeoPixels. We put this in an #if defined so it can
+    // be reused for other boards without compilation errors
+    pinMode(NEOPIXEL_POWER, OUTPUT);
+    digitalWrite(NEOPIXEL_POWER, HIGH);
+  #endif
+ pixels.begin();
+ pixels.setBrightness(60);
+ set_pixel(YELLOW);
+
+ USBDevice.setManufacturerDescriptor(mfgstr);
+ USBDevice.setProductDescriptor     (prodstr);
+
+ // Initialize MIDI, and listen to all MIDI channels
+ // This will also call usb_midi's and Serial1's begin()
+ midiA.begin(MIDI_CHANNEL_OMNI);
+ midiB.begin(MIDI_CHANNEL_OMNI);
+
+ midiA.turnThruOff();
+ midiB.turnThruOff();
+
+//  Serial.begin(115200);
+
+ // wait until device mounted
+ while ( !USBDevice.mounted() ) delay(1);
+ set_pixel(LED_COLOR);
+}
+
+void loop()
+{
+ // read any new MIDI messages
+ if ( midiA.read() ) {
+   midiB.send(midiA.getType(),
+              midiA.getData1(),
+              midiA.getData2(),
+              midiA.getChannel());
+   last_color = LED_DIM_COLOR;  // Update last color to red
+   pixel_on(LED_COLOR);
+   //  Serial.println("midiA");
+ }
+
+ if ( midiB.read() ) {
+   midiA.send(midiB.getType(),
+              midiB.getData1(),
+              midiB.getData2(),
+              midiB.getChannel());
+   last_color = LED_DIM_COLOR;  // Update last color to blue
+   pixel_on(LED_COLOR);
+   //  Serial.println("midiB");
+ }
+
+ pixel_check();
+}
+
+void pixel_check() {
+ if( led_on && (millis() - led_time) > led_on_time ) { 
+   led_on = false; 
+   set_pixel(last_color);  // Return to dimmed version of last active color
+ }
+}
+
+void pixel_on(uint32_t color) { 
+ set_pixel(color);
+ led_on = true;
+ led_time = millis();
+}
+
+void set_pixel(uint32_t color) {
+ pixels.setPixelColor(0, color);
+ pixels.show();
+}