DAXTROMN HYBRID SOLAR INVERTER 5KW PV IN 5000W 48V 80A CHARGER SOLAR CONTROLLER GRID TIED/OFF GRID SOLAR INVERTER PARALLEL

[MarekOleksik]

Hi,
I managed to connect to this inverter from Home Assistatnt according to description. I connected via the RS-232 port built into this inverter. Here is my configuration:

substitutions:
  name: esphome-web-827be8
  friendly_name: Daxtromn
  tx_pin: GPIO17
  rx_pin: GPIO16

esphome:
  name: ${name}
  friendly_name: ${friendly_name}
  min_version: 2024.6.0
  name_add_mac_suffix: false
  project:
    name: esphome.web
    version: '1.0'

esp32:
  board: esp32dev
  framework:
    type: arduino

# Enable logging
logger:
  hardware_uart: UART1
  level: very_verbose

# Enable Home Assistant API
api:

# Allow Over-The-Air updates
ota:
- platform: esphome

# Allow provisioning Wi-Fi via serial
# improv_serial:

wifi:
  domain: .lan
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  power_save_mode: none
  manual_ip:
    static_ip: X.X.X.X
    gateway: X.X.X.X
    subnet: 255.255.255.0
    dns1: 8.8.8.8
  # Set up a wifi access point
  ap: {}

# In combination with the `ap` this allows the user
# to provision wifi credentials to the device via WiFi AP.
captive_portal:

# Sets up Bluetooth LE (Only on ESP32) to allow the user
# to provision wifi credentials to the device.
# esp32_improv:
#   authorizer: none

external_components:
  - source: github://syssi/esphome-pipsolar@2424mse1
    refresh: 0s

# To have a "next url" for improv serial
web_server:

uart:
  - id: uart_0
    baud_rate: 2400
    tx_pin: ${tx_pin}
    rx_pin: ${rx_pin}
    # debug:
    #   direction: BOTH
    #   dummy_receiver: false
    #   after:
    #     delimiter: "\r"
    #   sequence:
    #     - lambda: UARTDebug::log_string(direction, bytes);

dashboard_import:
  package_import_url: github://esphome/example-configs/esphome-web/esp8266.yaml@main
  import_full_config: true

pipsolar:
  - id: inverter0
    uart_id: uart_0

i2c:
  sda: GPIO21
  scl: GPIO22
  scan: false

sensor:
  - platform: bme280_i2c
    address: 0x76
    temperature:
      name: "Temperatura otoczenia Daxtromn"
    pressure:
      name: "Ciśnienie atmosferyczne"
    humidity:
      name: "Wilgotność"

  - platform: pipsolar
    pipsolar_id: inverter0
    grid_rating_voltage:
      id: inverter0_grid_rating_voltage
      name: "Napięcie znamionowe sieci"
    grid_rating_current:
      id: inverter0_grid_rating_current
      name: "Prąd znamionowy sieci"
    grid_voltage:
      id: inverter0_grid_voltage
      name: "Napięcie sieci"
    grid_frequency:
      id: inverter0_grid_frequency
      name: "Częstotliwość sieci"
    ac_output_rating_voltage:
      id: inverter0_ac_output_rating_voltage
      name: "Napięcie znamionowe wyjścia AC"
    ac_output_rating_frequency:
      id: inverter0_ac_output_rating_frequency
      name: "Częstotliwość znamionowa wyjścia AC"
    ac_output_rating_current:
      id: inverter0_ac_output_rating_current
      name: "Prąd znamionowy wyjścia AC"
    ac_output_rating_apparent_power:
      id: inverter0_ac_output_rating_apparent_power
      name: "Moc pozorna wyjścia AC"
    ac_output_rating_active_power:
      id: inverter0_ac_output_rating_active_power
      name: "Moc czynna wyjścia AC"
    ac_output_voltage:
      id: inverter0_ac_output_voltage
      name: "Napięcie wyjściowe AC"
    ac_output_frequency:
      id: inverter0_ac_output_frequency
      name: "Częstotliwość wyjściowa AC"
    ac_output_apparent_power:
      id: inverter0_ac_output_apparent_power
      name: "Moc pozorna wyjściowa AC"
    ac_output_active_power:
      id: inverter0_ac_output_active_power
      name: "Moc czynna wyjściowa AC"
    battery_rating_voltage:
      id: inverter0_battery_rating_voltage
      name: "Napięcie znamionowe baterii"
    battery_bulk_voltage:
      id: inverter0_battery_bulk_voltage
      name: "Napięcie bulk baterii"
    battery_type:
      id: inverter0_battery_type
      name: "Typ baterii"
    battery_voltage:
      id: inverter0_battery_voltage
      name: "Napięcie baterii"
    battery_charging_current:
      id: inverter0_battery_charging_current
      name: "Prąd ładowania baterii"
    battery_capacity_percent:
      id: inverter0_battery_capacity_percent
      name: "Procent pojemności baterii"
    battery_voltage_scc:
      id: inverter0_battery_voltage_scc
      name: "Napięcie baterii SCC"
    battery_discharge_current:
      id: inverter0_battery_discharge_current
      name: "Prąd rozładowywania baterii"
    battery_voltage_offset_for_fans_on:
      id: inverter0_battery_voltage_offset_for_fans_on
      name: "Offset napięcia baterii dla załączenia wentylatora"
    current_max_ac_charging_current:
      id: inverter0_current_max_ac_charging_current
      name: "Maksymalny prąd ładowania AC"
    current_max_charging_current:
      id: inverter0_current_max_charging_current
      name: "Maksymalny prąd ładowania"
    # output_source_priority:
    #   id: inverter0_output_source_priority
    #   name: "Priorytet źródła - wyjście"
    charger_source_priority:
      id: inverter0_charger_source_priority
      name: "Priorytet źródła - ładowarka"
    parallel_max_num:
      id: inverter0_parallel_max_num
      name: "Maksymalna liczba równoległych urządzeń"
    machine_type:
      id: inverter0_machine_type
      name: "Typ urządzenia"
    topology:
      id: inverter0_topology 
      name: "Topologia"
    output_mode:
      id: inverter0_output_mode
      name: "Typ wyjścia"
    battery_redischarge_voltage:
      id: inverter0_battery_redischarge_voltage
      name: "Napięcie ponownego rozładowania baterii"
    output_load_percent:
      id: inverter0_output_load_percent
      name: "Procent obciążenia wyjścia"
    bus_voltage:
      id: inverter0_bus_voltage
      name: "Napięcie magistrali"
    inverter_heat_sink_temperature:
      id: inverter0_inverter_heat_sink_temperature
      name: "Temperatura radiatora"
    pv_input_current_for_battery:
      id: inverter0_pv_input_current_for_battery
      name: "Prąd wejściowy baterii PV"
    pv_input_voltage:
      id: inverter0_pv_input_voltage
      name: "Napięcie wejściowe PV"
    pv_charging_power:
      id: inverter0_pv_charging_power
      name: "Moc paneli PV"
      filters:
        - multiply: 0.001
      unit_of_measurement: kWh
      device_class: energy
      state_class: total_increasing
      accuracy_decimals: 3
    eeprom_version:
      id: inverter0_eeprom_version 
      name: "Wersja EEPROM"
  
  - platform: template
    name: " Baterie - ładowanie "
    filters:
      - multiply: 0.001
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing
    accuracy_decimals: 3
    lambda: |-
          float i = 314 + id(inverter0_battery_charging_current).state;
          float e = id(inverter0_battery_voltage).state;
          float w = 0.0;
          if (i > 0) {
            w =  i * e;
          }
          return {w};

  - platform: template
    name: " Baterie - rozładowanie "
    filters:
      - multiply: 0.001
    unit_of_measurement: kWh
    device_class: energy
    state_class: total_increasing
    accuracy_decimals: 3
    lambda: |-
          float i = id(inverter0_battery_discharge_current).state;
          float e = id(inverter0_battery_voltage).state;
          float w = 0.0;
          if (i < 0) {
            w = i * e;
          }
          return {w * -1};
    
binary_sensor:
  - platform: pipsolar
    pipsolar_id: inverter0
    add_sbu_priority_version:
      id: inverter0_add_sbu_priority_version
      name: "Dodaj priorytet SBU"
    configuration_status:
      id: inverter0_configuration_status
      name: "Status konfiguracji"
    scc_firmware_version:
      id: inverter0_scc_firmware_version
      name: "Wersja oprogramowania"
    load_status:
      id: inverter0_load_status 
      name: "Stan wejścia"
    battery_voltage_to_steady_while_charging:
      id: inverter0_battery_voltage_to_steady_while_charging 
      name: "Napięcie stabilizacji akumulatora podczas ładowania"
    charging_status:
      id: inverter0_charging_status 
      name: "Stan ładowania"
    scc_charging_status:
      id: inverter0_scc_charging_status  
      name: "Stan ładowania SCC"
    ac_charging_status:
      id: inverter0_ac_charging_status  
      name: "Stan ładowania SCC"
    charging_to_floating_mode:
      id: inverter0_charging_to_floating_mode
      name: "Ładowanie do trybu pływającego"
    switch_on:
      id: inverter0_switch_on
      name: "Włączenie"
    # dustproof_installed:
    #   id: inverter0_dustproof_installed
    #   name: "Pyłoszczelna zainstalowana"
    silence_buzzer_open_buzzer:
      id: inverter0_silence_buzzer_open_buzzer
      name: "Buzzer wyciszony"
    overload_bypass_function:
      id: inverter0_overload_bypass_function
      name: 'Przeciążenie funkcji bypasu'
    lcd_escape_to_default:
      id: inverter0_lcd_escape_to_default
      name: "Wyjście do ekranu głównego"
    overload_restart_function:
      id: inverter0_overload_restart_function
      name: "Restart po przeciążeniu"
    over_temperature_restart_function:
      id: inverter0_over_temperature_restart_function
      name: "Restart po wysokiej temperaturze"
    backlight_on:
      id: inverter0_backlight_on
      name: "Podświetlenie włączone"
    alarm_on_when_primary_source_interrupt:
      id: inverter0_alarm_on_when_primary_source_interrupt
      name: "Alarm, kiedy brak głównego źródła"
    fault_code_record:
      id: inverter0_fault_code_record
      name: "Zapisz kod błędu"
    power_saving:
      id: inverter0_power_saving
      name: "Oszczędzanie energii"
    warnings_present:
      id: inverter0_warnings_present
      name: "Obecność ostrzeżeń"
    faults_present:
      id: inverter0_faults_present
      name: "Obecność błędów"
    warning_power_loss:
      id: inverter0_warning_power_loss 
      name: "Ostrzeżenie - utrata mocy"
    fault_inverter_fault:
      id: inverter0_fault_inverter_fault
      name: "Błąd inwertera"
    fault_bus_over:
      id: inverter0_fault_bus_over
      name: "Błąd bus over"
    fault_bus_under:
      id: inverter0_fault_bus_under
      name: "Błąd bus under"
    fault_bus_soft_fail:
      id: inverter0_fault_bus_soft_fail
      name: "Błąd bus soft_fail"
    warning_line_fail:
      id: inverter0_warning_line_fail
      name: "Ostrzeżenie - błąd linii"
    fault_opvshort:
      id: inverter0_fault_opvshort
      name: "Błąd opvshort"
    fault_inverter_voltage_too_low:
      id: inverter0_fault_inverter_voltage_too_low 
      name: "Błąd - za niskie napięcie inwertera"
    fault_inverter_voltage_too_high:
      id: inverter0_fault_inverter_voltage_too_high
      name: "Błąd - za wysokie napięcie inwertera"
    warning_over_temperature:
      id: inverter0_warning_over_temperature
      name: "Ostrzeżenie - za wysoka temperatura"
    warning_fan_lock:
      id: inverter0_warning_fan_lock
      name: "Ostrzeżenie - zablokowany wentylator"
    warning_battery_voltage_high:
      id: inverter0_warning_battery_voltage_high
      name: "Ostrzeżenie - za wysokie napięcie baterii"
    warning_battery_low_alarm:
      id: inverter0_warning_battery_low_alarm 
      name: "Ostrzeżenie - za niskie napięcie baterii"
    warning_battery_under_shutdown:
      id: inverter0_warning_battery_under_shutdown
      name: "Ostrzeżenie - bateria blisko odcięcia"
    warning_battery_derating:
      id: inverter0_warning_battery_derating
      name: "Ostrzeżenie - obniżone wartości znamionowe baterii"
    warning_over_load:
      id: inverter0_warning_over_load
      name: "Ostrzeżenie - przeciążenie"
    warning_eeprom_failed:
      id: inverter0_warning_eeprom_failed
      name: "Ostrzeżenie - błąd EEPROM"
    fault_inverter_over_current:
      id: inverter0_fault_inverter_over_current
      name: "Błąd - za wysoki prąd inwertera"
    fault_inverter_soft_failed:
      id: inverter0_fault_inverter_soft_failed 
      name: "Błąd oprogramowania inwertera"
    fault_self_test_failed:
      id: inverter0_fault_self_test_failed
      name: "Błąd autodiagnostyki"
    fault_op_dc_voltage_over:
      id: inverter0_ault_op_dc_voltage_over
      name: "Błąd - za wysokie napięcie DC"
    fault_battery_open:
      id: inverter0_fault_battery_open
      name: "Błąd - brak baterii"
    fault_current_sensor_failed:
      id: inverter0_fault_current_sensor_failed
      name: "Błąd - uszkodzenie czujnika prądu"
    fault_battery_short:
      id: inverter0_fault_battery_short
      name: "Błąd - zwarcie baterii"
    warning_power_limit:
      id: inverter0_warning_power_limit
      name: "Ostrzeżenie - limit mocy"
    warning_pv_voltage_high:
      id: inverter0_warning_pv_voltage_high
      name: "Ostrzeżenie - za duże napięcie PV"
    fault_mppt_overload:
      id: inverter0_fault_mppt_overload
      name: "Bład - przeciążenie MPPT"
    warning_mppt_overload :
      id: inverter0_warning_mppt_overload 
      name: "Ostrzeżenie - przeciążenie MPPT"
    warning_battery_too_low_to_charge:
      id: inverter0_warning_battery_too_low_to_charge
      name: "Ostrzeżenie - za niskie napięcie baterii do ładowania"
    fault_dc_dc_over_current:
      id: inverter0_fault_dc_dc_over_current
      name: "Błąd - za wysoki prąd DC"
    fault_code:
      id: inverter0_fault_code
      name: "Kod błędu"
    warnung_low_pv_energy:
      id: inverter0_warning_low_pv_energy
      name: "Ostrzeżenie - za niska energia PV"
    warning_high_ac_input_during_bus_soft_start:
      id: inverter0_warning_high_ac_input_during_bus_soft_start
      name: "Ostrzeżenie - za wysokie wejście AC podczas soft startu magistrali"
    warning_battery_equalization:
      id: inverter0_warning_battery_equalization
      name: "Ostrzeżenie - wyrównywanie baterii"

text_sensor:
  - platform: pipsolar
    pipsolar_id: inverter0
    device_mode:
      id: inverter0_device_mode
      name: "Tryb falownika"
    # last_qpigs:
    #   id: inverter0_last_qpigs
    #   name: "Ostatnia komenda qpigs"
    # last_qpiri:
    #   id: inverter0_last_qpiri
    #   name: "Ostatnia komenda qpiri"
    # last_qmod:
    #   id: inverter0_last_qmod
    #   name: "Ostatnia komenda qmod"
    # last_qflag:
    #   id: inverter0_last_qflag
    #   name: "Ostatnia komenda qflag"
    # last_qpiws:
    #   id: inverter0_last_qpiws
    #   name: "Ostatnia komenda qpiws"
    # last_qt:
    #   id: inverter0_last_qt
    #   name: "Ostatnia komenda qt"
    # last_qmn:
    #   id: inverter0_last_qmn
    #   name: "Ostatnia komenda qmn"

switch:
  - platform: pipsolar
    pipsolar_id: inverter0
    output_source_priority_utility:
      id: inverter0_output_source_priority_utility
      name: "Priorytet źródła - falownik"
    output_source_priority_solar:
      id: inverter0_output_source_priority_solar
      name: "Priorytet źródła - solary"
    output_source_priority_battery:
      id: inverter0_output_source_priority_battery
      name: "Priorytet źródła - bateria"
    # input_voltage_range:
    #   id: inverter0_input_voltage_range
    #   name: "Zakres napięcia wejściowego"
    pv_ok_condition_for_parallel:
      id: inverter0_pv_ok_condition_for_parallel
      name: "PV warunek ok dla równoległości"
    pv_power_balance:
      id: inverter0_pv_power_balance
      name: "Balans mocy PV"

  - platform: restart
    icon: mdi:reload-alert
    name: "Daxtromn Restart"

output:
  - platform: pipsolar
    pipsolar_id: inverter0
    battery_recharge_voltage:
      id: inverter0_battery_recharge_voltage
      possible_values: 
        - 44.0
        - 45.0 
        - 46.0 
        - 47.0
        - 48.0 
        - 49.0
        - 50.0
        - 51.0
    battery_under_voltage:
      id: inverter0_battery_under_voltage
      possible_values: 
        - 40.0
        - 40.1
        - 42
        - 43
        - 44
        - 45
        - 46
        - 47
        - 48.0
    battery_float_voltage:
      id: inverter0_battery_float_voltage
      possible_values: 
        - 48.0
        - 49.0
        - 50.0
        - 51.0

select:
  - platform: pipsolar
    pipsolar_id: inverter0
    output_source_priority:
      id: inverter0_output_source_priority_select
      name: "Priorytet źródła - wyjście"
      optionsmap:
        "Utility first": "POP00"
        "Solar only": "POP01"
        "Solar Battery Utility": "POP02"
      statusmap:
        "0": "Utility first"
        "1": "Solar only"
        "2": "Solar Battery Utility"

Could you check it and say what can I improve. Thanks.

It looks like this:

This inverter has also ability to connect over wifi, but I couldn't integrate it with Home Assistant. I checked the control board on this inverter and looks like this:

It has built-in esp01s. I can connect from phone over wifi with this inverter and in application Wifimonitor I can check the inverter's parameters. Do you think I can connect with this esp and do something on it from Home Assistant? I am new on esp, that's why I am asking ;-)

[syssi]

I'm confused. Does the pipsolar component work in general?

[MarekOleksik]

Yes, it works perfectly. Good job. I can view all parameters in home assistant. But I wonder if I can use the built-in esp which is on the inverter, and how to add entity to measure energy generated by this inverter to add to energy panel in home assistant.

[syssi]

Is the ESP01S soldered to the mainboard or could you replace the ESP easily?

You could attach another ESP to RXD and TXD to sniff the communication between the mainboard and the ESP01S. Flash this YAML configuration to the sniffing ESP: https://github.com/syssi/esphome-seplos-bms/blob/main/tests/esp8266-uart-sniffer.yaml

[MarekOleksik]

The ESP01S is soldered to the mainboard. When I find some time, I will solder my esp with this sniffer to the built-in one and check what will happen ;)

[syssi]

If you are lucky the ESP uses the same protocol as pipsolar and acts as a "remote control" of your inverter.

[mirkok19288]

Hallo. ich wollte mal fragen ob es zu diesem Thema was neues gibt ? ich habe den selben inverter und möchte ihn in homeassisten hinzufügen.

[syssi]

Das Gerät wird grundsätzlich unterstützt, wenn man es über RS232 ansteuert. Ich werde keine Anstrengungen unternehmen das WiFi-Board mit anderer Firmware zu versehen.