Gecko not in grub

[gordon3913]

I installed Geckolinux Mate rolling but there is no entry in grub for me to login.

[geckolinux]

Hi there, in order to help we would need more information. Which ISO version did you use to install, which partitioning option you chose, whether it's a UEFI or legacy BIOS system, if you saw any errors during installation, etc.

[gordon3913]

iso version 210526, manual partitioning (wanted a separate home partition), chose UEFI. No errors occurred during installation.

…

On Sun, 13 Jun 2021 at 23:44, GeckoLinux ***@***.***> wrote: Hi there, in order to help we would need more information. Which ISO version did you use to install, which partitioning option you chose, whether it's a UEFI or legacy BIOS system, if you saw any errors during installation, etc. — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#251 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AUOX563ESR3HLHJXUTKAFJLTSSY2RANCNFSM46TN65XQ> .

-- Gordon Loughnan Phone: 0478 620080 Email: ***@***.***

[geckolinux]

Hi again, did you remember to configure /boot/efi to be mounted and set the appropriate flags?

[gordon3913]

Yes, I did.

…

On Mon, 14 Jun 2021 at 10:03, GeckoLinux ***@***.***> wrote: Hi again, did you remember to configure /boot/efi to be mounted and set the appropriate flags? — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#251 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AUOX565FEM4O6IPQS3FT32LTSVBNNANCNFSM46TN65XQ> .

-- Gordon Loughnan Phone: 0478 620080 Email: ***@***.***

[geckolinux]

Please re-install it, and include a screenshot of the partitioning step and of the final overview page before installation starts.

[gordon3913]

sorry screenshot did not work but I have listed the installed partitions. I am able to boot Gecko by clicking esc on boot, then f9 to select the Gecko partition.
gordon@gordon-hp250g4Geko:~> df -h
Filesystem Size Used Avail Use% Mounted on
devtmpfs 3.8G 8.0K 3.8G 1% /dev
tmpfs 3.9G 0 3.9G 0% /dev/shm
tmpfs 1.6G 18M 1.6G 2% /run
/dev/sda5 179G 4.4G 174G 3% /
tmpfs 3.9G 4.0K 3.9G 1% /tmp
/dev/sda5 179G 4.4G 174G 3% /home
/dev/sda1 93M 11M 83M 11% /boot/efi
tmpfs 779M 72K 779M 1% /run/user/1000

[geckolinux]

OK, thanks. Does your computer have Secure Boot enabled in the UEFI settings? If so, once you have booted into your GeckoLinux installation please try using the YaST Bootloader tool to adjust the default boot entry and the timeout seconds, and then apply the changes, that will make YaST install the EFI bits it needs to support SecureBoot. And/or you might need to go into your computer's UEFI settings and set the GeckoLinux bootloader as the default one. Sorry I can't give more specific instructions, as each UEFI system and configuration is different.

[gordon3913]

Ok, I'll check it out.

…

On Wed, 16 Jun 2021 at 23:43, GeckoLinux ***@***.***> wrote: OK, thanks. Does your computer have Secure Boot enabled in the UEFI settings? If so, once you have booted into your GeckoLinux installation please try using the YaST Bootloader tool to adjust the default boot entry and the timeout seconds, and then apply the changes, that will make YaST install the EFI bits it needs to support SecureBoot. And/or you might need to go into your computer's UEFI settings and set the GeckoLinux bootloader as the default one. Sorry I can't give more specific instructions, as each UEFI system and configuration is different. — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#251 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AUOX564WRFCWC55EKQQ7UUTTTCTB5ANCNFSM46TN65XQ> .

-- Gordon Loughnan Phone: 0478 620080 Email: ***@***.***