Replies: 4 comments 17 replies
-
|
Hello.... This worked until version 9.1.96 ( I had this Early Access and worked). When become the new 9.1.105 stoped (related in past this issue). |
Beta Was this translation helpful? Give feedback.
-
|
To work again I performed the downgrade of Network Application....... |
Beta Was this translation helpful? Give feedback.
-
|
Thanks for the reply @dancautella. I do want to keep up with the Network releases, so I prefer to search for a solution instead of downgrading. I'll find a different way to watch TV in the mean time. |
Beta Was this translation helpful? Give feedback.
-
|
What UniFi device do you have? I’ve been running on Network Application 9.1 on an UDM Pro without any issues since it became available in Early Access, currently on 9.1.120. You might want to try a reinstall of the script to see if that works. Or check for any errors or other messages in the logs to troubleshoot. |
Beta Was this translation helpful? Give feedback.
-
|
Hi @erikpost, thanks a lot for your response and questions! I have a UXG pro, which worked correctly for the last 2 years, with an occasional re-installation of the service (after firmware updates). Note: this was with lan interface eth3.661, which doesn't seem correct, as it won't let me start the proxy at this time. What I did until now:
I'm wondering, could this somehow be related to changes in 9.1 that are related to the zone based firewall? I've added configuration and logs for reference. My configuration currently (like I said, a bit different from what was used/working the previous 2 years): This leads to the following
The logs The logs, to me, don't show any obvious errors, but once I switch my TV box on I start to see a lot of these: |
Beta Was this translation helpful? Give feedback.
-
|
Don't see any strange things, both in config and logs. For UXG series I think you indeed need brxxx for the local VLAN interface, not 100% sure though since I don't have experience with the UXG. I'm using Zone Based Firewall on my UDM Pro, and that doesn't interfere with using IPTV. But be sure to check your rules to see if they are set up correctly. What you could try is switching to igmpproxy instead of improxy (the default). To do that install igmpproxy with |
Beta Was this translation helpful? Give feedback.
-
|
Hi @erikpost, thanks for your reply. Good to know it's probably not the firewall, I think I only have some default rules configured, nothing special. Also, I already tried to go the igmpproxy way, but unfortunately that did not result in anything different. |
Beta Was this translation helpful? Give feedback.
-
|
ISP KPN ? This is my active UCG-Fiber config which works fine with 9.1.120, could you test this configuration. KPN uses IGMPv2: Also IGMP snooping on your UniFi LAN switch should be disabled during troubleshooting. A switch can suspend multicast streams too. |
Beta Was this translation helpful? Give feedback.
-
|
Did you compare my config with yours and made the correct enhancements on yours, except from the interfaces? |
Beta Was this translation helpful? Give feedback.
-
|
Beta Was this translation helpful? Give feedback.
-
|
I have the same thing, but it doesn't work. I can also configure fast leave, but enabling or disabling that one doesn't seem to have any effect. |
Beta Was this translation helpful? Give feedback.
-
|
Did you disable the IGMP proxy under the WAN port settings, that should be unchecked. Please provide some logs just after the start of udm-iptv and after zapping around on the tv. |
Beta Was this translation helpful? Give feedback.
-
|
IGMP Proxy for the WAN is turned off. Here are some logs after starting: After these initial logs I get a lot of these: If I zap around, these logs are added: |
Beta Was this translation helpful? Give feedback.
-
|
Could you explain a bit more the issues you are facing because the logs does not show big warnings. Does the stream start, does it run 15-20 seconds or 4 minutes 30 seconds? Do you see LIVE or Live in the right lower corner? Does it stream with Live (unicast) if you change the settings to unicast in the config of the STB? |
Beta Was this translation helpful? Give feedback.
-
|
The stream runs for 1-2 seconds and then freezes, it will then run again for 1-2 seconds before showing the |
Beta Was this translation helpful? Give feedback.
-
|
Sorry @spiralshapeturtle, I removed my previous comment because, after a couple of minutes, the things I said didn't make sense anymore. I'm back to square one. It doesn't seem to matter if I enable/disable IGMP Snooping, nor Fast Leave. I don't see any obvious mistakes in the logs as well. |
Beta Was this translation helpful? Give feedback.
Uh oh!
There was an error while loading. Please reload this page.
-
Hi everyone, I recently upgraded Unifi Network to version 9.1. My TV immediately froze, and I haven’t been able to fix it since. Does anyone else face the same issue, or have any idea what it could be? I can provide configuration and logs if needed. Thanks!
Beta Was this translation helpful? Give feedback.
All reactions