no way to make it show using CTRL+SHIFT+P

[laverdanny]

hi
tried several times on 2 different computers to install, no way to make it work

[laverdanny]

Hi

As you told to @MrPretendo

I followed the instructions I installed it in C:\Users<username>.arduinoIDE\plugins\ that I created on purpose

I contacted Arduino support too, they don't seem to be really aware of "plugins" existence, but suggeste me to install in C:\Users<username>.arduinoIDE\extensions, things I tried to do unsuccesfully

Have you any suggestions, or a ways (logs ?) to discover what's going on ?

Regards

[moonpuppy-linus]

Hi @laverdanny, I was trying the same thing and having the same problem today.

I went back to the instructions and made sure I restarted the Arduino IDE, and when I did [Ctrl]+[Shift]+[P], I still didn't see Upload LittleFS to Pico/ESP8266/ESP32 in the list.

Then it hit me that it's a really long list with a search box at the top ("> ").

I scrolled way down and found it in the list, then went back to the top and typed in "Upload". That trimmed down the list considerably and "Upload LittleFS to Pico/ESP8266/ESP32" was one of the 3 entries.

I apologize if I'm overstating the obvious and this doesn't help at all. -lw

[laverdanny]

It's my turn to aploogize !!!

You're right, CTRL+SHIFT+P pop up a menu, but no scroll bar on the side if you don't move the mouse into the list !

It's a very long list, and Upload is in too

Thanks a lot !

[kellnerp]

Also cannot see the command for littlefs or spiffs using ctrl-shft-P.

LAP2:~/.arduino15/plugins$ ls
arduino-littlefs-upload-1.5.3.vsix

Ubuntu 20.04
ESP32 WROOM 32E
Arduino 2.3.5
ESP32 DEV MODULE

[earlephilhower]

Please carefully read the installation message. That's not the right spot to put the file.
https://github.com/earlephilhower/arduino-littlefs-upload?tab=readme-ov-file#installation

[kellnerp]

Earl, Thanks for the response. I have placed it here on a Ubuntu 20.04 installation with ArduinoIDE 2.3.5: ~/.arduinoIDE/plugins/arduino-littlefs-upload-1.5.3.vsix I don't see it in the list after CTRL-SHFT-M even after changing the board definition or starting a new sketch. I am using the Espressif ESP32 Dev Module board definition which is not mentioned in the readme. The only reason I assume this plugin works is that other websites recommend it, but it might not be what you intended. Paul B. Kellner #################################################################### Check out my favorite tunes at PocketVinyl. http://www.pocketvinyl.com/ -----Original Message----- From: earlephilhower/arduino-littlefs-upload ***@***.***> Sent: Mar 20, 2025 1:52 AM To: earlephilhower/arduino-littlefs-upload ***@***.***> Cc: kellnerp ***@***.***>, Comment ***@***.***> Subject: Re: [earlephilhower/arduino-littlefs-upload] no way to make it show using CTRL+SHIFT+P (Discussion #89) Please carefully read the installation message. That's not the right spot to put the file. https://github.com/earlephilhower/arduino-littlefs-upload?tab=readme-ov-file#installation &mdash; Reply to this email directly, view it on GitHub (#89 (reply in thread)), or unsubscribe (https://github.com/notifications/unsubscribe-auth/AEF6VFLBRVUTDHJUCRE2CXT2VGOD3AVCNFSM6AAAAABZGSIQHWVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTENJVGQ3TMOI). You are receiving this because you commented.Message ID: ***@***.***>

[earlephilhower]

Not sure if that was a typo, but it's CTRL+SHIFT+P to get the command menu, then type "upl" to search for it.