KNX State Messages no longer received

[albertv0]

Hello,
After a recent update (not sure which one) I stopped receiving any state messages.
Connection seems working fine, I am able to send control messages from Node-Red to the KNX bus to control things (lights, etc.).
However, when a device is switched on or off, nothing is received on Node-Red for the relevant state group address.
It used to work just fine.
Any obvious thing comes to mind?
I have "react to write telegrams" activated.

Best,
Albert

[Supergiovane]

Hi
If you come from a very old version, please check the gateway config window and make sure all settings are fine and filled in.

[albertv0]

Checked, everything looks fine. I can control the devices, so connection is ok. El lun, 2 jun 2025 a las 12:00, Massimo Saccani ***@***.***>) escribió:

…

Hi If you come from a very old version, please check the gateway config window and make sure all settings are fine and filled in. — Reply to this email directly, view it on GitHub <#448 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A77UDGPSPWLYAT373TRLFL33BQOELAVCNFSM6AAAAAB6MPDM7KVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMZUGE3TOMA> . You are receiving this because you authored the thread.Message ID: <Supergiovane/node-red-contrib-knx-ultimate/repo-discussions/448/comments/13341770 @github.com>

-- Albert Vila * ***@***.***>*

[albertv0]

I tried using the KNX viewer node and nothing comes through, except the messages sent from Node-Red, El lun, 2 jun 2025 a las 12:13, Albert Vila ***@***.***>) escribió:

…

Checked, everything looks fine. I can control the devices, so connection is ok. El lun, 2 jun 2025 a las 12:00, Massimo Saccani ***@***.***>) escribió: > Hi > If you come from a very old version, please check the gateway config > window and make sure all settings are fine and filled in. > > — > Reply to this email directly, view it on GitHub > <#448 (comment)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/A77UDGPSPWLYAT373TRLFL33BQOELAVCNFSM6AAAAAB6MPDM7KVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMZUGE3TOMA> > . > You are receiving this because you authored the thread.Message ID: > <Supergiovane/node-red-contrib-knx-ultimate/repo-discussions/448/comments/13341770 > @github.com> > -- Albert Vila * ***@***.***>*

-- Albert Vila * ***@***.***>*

[Supergiovane]

Do you have restarted node red, right?
Please check also the config where you can select the ethernet interface to bind to. Check you’ve choosen the right one.
if you still have issues, i need you to fill the fields requested when you open an issue. Without that, i can’t do more to help you.

[albertv0]

Yes, I tried that as well. I just temporarily installed and configured KNX-easy, with just 1 one random device. KNX ultimate started to work again (all devices). I uninstalled KNX-easy again and it still works normally. It's not the first time that this does the trick. El lun, 2 jun 2025 a las 12:29, Massimo Saccani ***@***.***>) escribió:

…

Do you have restarted node red, right? Please check also the config where you can select the ethernet interface to bind to. Check you’ve choosen the right one. if you still have issues, i need you to fill the fields requested when you open an issue. Without that, i can’t do more to help you. — Reply to this email directly, view it on GitHub <#448 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A77UDGLDYVPRMFAG2CNWEIL3BQRSJAVCNFSM6AAAAAB6MPDM7KVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMZUGIYDGNQ> . You are receiving this because you authored the thread.Message ID: <Supergiovane/node-red-contrib-knx-ultimate/repo-discussions/448/comments/13342036 @github.com>

-- Albert Vila * ***@***.***>*