my DSM Version: 918+_7.0.1_42218 problem: Preventing Storage Pool Creation,Health Status Not Supported #26
Description
my DSM Version: 918+_7.0.1_42218
HBA card: LSI 9400 16i
problem: Preventing Storage Pool Creation,Health Status Not Supported
but in terminal use smartctl , I got normal information.
root@test:/etc# smartctl -a /dev/sdj
smartctl 6.5 (build date Feb 20 2021) [x86_64-linux-4.4.180+] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Ultrastar
Device Model: WDC WUH721818ALE6L4
Serial Number: 3WKVUKLK
LU WWN Device Id: 5 000cca 284f67823
Firmware Version: PCGNW232
User Capacity: 18,000,207,937,536 bytes [18.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: Unknown(0x0ffc) (unknown minor revision code: 0x009c)
SATA Version is: SATA >3.2 (0x1ff), 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Oct 15 12:16:49 2021 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 101) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1894) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 099 099 001 Pre-fail Always - 25769803845
4 Start/Stop_Count 0x0012 100 100 000 Old_age Always - 1
5 Reallocated_Sector_Count 0x0033 100 100 001 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 001 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0
9 Power-On_Hours_Count 0x0012 100 100 000 Old_age Always - 17
10 Spin_Retry_Count 0x0013 100 100 001 Pre-fail Always - 0
12 Device_Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1
22 Internal_Environment_Status 0x0023 100 100 025 Pre-fail Always - 100
192 Power_off_Retract_Count 0x0032 100 100 000 Old_age Always - 5
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 5
194 Temperature 0x0002 046 046 000 Old_age Always - 46 (Min/Max 25/47)
196 Reallocation_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector_Count 0x0022 100 100 000 Old_age Always - 0
198 Off-Line_Scan_Uncorrectable_Sector_Count 0x0008 100 100 000 Old_age Offline - 0
199 Ultra_DMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute `delay.`
so any idea?
Originally posted by @ranydb in #14 (comment)