VCU118 hangs at loading Linux from SD Card

[khoatm98]

Hi everyone,
I tried to get this project worked on VCU118.

I tried to implement the workaround solution in #65 but it still does not work. I also tried to modify the clock divider on sd card and modify the VADJ.

The system always get stuck at
sd initialized!
initializing SD...
sd initialized!
copying block 0 of 1 blocks (0 %)

Is there anything else that I need to check?
Thank you very much.

[khoatm98]

Sorry, this issue is redundant.

[Jbalkind]

This is the first week of our teaching quarter so I wasn't keeping up. Did you figure it out?

[khoatm98]

Yes, it seems like the connection is not stable all the time, we need to reset the CPU several times until it can read data from SD card.

[Jbalkind]

That is frustrating. Unfortunately we don't have a vcu118 of our own. Ultimately I think Xilinx's decision to deprioritise low speed I/O on ultrascale+ seems to make this kind of issue inevitable. I do wonder whether further reducing the SD frequency might help?

[khoatm98]

I will try reducing SD frequency and let you you the result asap. By the way, currently I also want to try the solution booting without SD card mentioned in https://groups.google.com/g/openpiton/c/STQLcZMDOeI/m/wZUfb2z3AgAJ as a work around solution.

[khoatm98]

Hi @Jbalkind,

I tried to reduce the clock frequency for SD but the result still remains the same.
I tried booting Linux by pitonstream and it works fine. However, in both cases (loading from SD card and by pitonstream), I could only get few information printed out the console and the program could never boot up successfully. I also tried the ariane image on the website as well as rebuilding one myself.

I wonder if you have any experience about this situation.

Thank you,
Khoa.
screen.txt

[Jbalkind]

I would recommend against using UART for Linux boot. It's pretty likely that there could be a data corruption over the course of loading the whole bitstream. Perhaps you could try JTAG? There is a bscane2 config in the RTL that you could set up and try loading the kernel image using openocd and gdb. It's a lot faster and more reliable than UART.

[khoatm98]

Thank you @Jbalkind ,

I will try it this week and let you know the result.

[khoatm98]

Hi @Jbalkind ,

Now, I have been trying Openocd but the result is not optimistic. I checked the schematic and the Bscane2 module is already there. I want to confirm that whether it is necessary to connect our host machine to the FPGA board via GPIO pins or we can just use the micro-USB port labeled with JTAG.

Thank you.

[Jbalkind]

I believe bscane2 is on the regular JTAG chain with the micro usb

[jimaandro]

I would recommend against using UART for Linux boot. It's pretty likely that there could be a data corruption over the course of loading the whole bitstream. Perhaps you could try JTAG? There is a bscane2 config in the RTL that you could set up and try loading the kernel image using openocd and gdb. It's a lot faster and more reliable than UART.

Hello!

I have a similar issue. I would prefer to use only the UART and pitonstream instead of GDB.
How can I write the bbl.bin to RAM?
If I use pitonstream then uart boot should be enabled. This chooses the baremetal bootROM.
So should I change this to use the linux bootrom without copying from SD card?
@khoatm98 How did you managed to pitonstream the linux image?

Thanks!

[khoatm98]

hi @jimaandro
Yes I can use UART for linux boost but I could take a while (~10minutes).
Just use your bbl (place it at openpiton/piton/verif/diag) as a prebuild image and run pitonstream script to download the image to FPGA board.
For this, you would need to comment the line that is used to copy data from SD card to RAM in bootroom source and regenerate bitstream.
However, it works but i don't recommend to do it this way. You can use openOCD to donwload the image instead.

[jimaandro]

hi @jimaandro Yes I can use UART for linux boost but I could take a while (~10minutes). Just use your bbl (place it at openpiton/piton/verif/diag) as a prebuild image and run pitonstream script to download the image to FPGA board. For this, you would need to comment the line that is used to copy data from SD card to RAM in bootroom source and regenerate bitstream. However, it works but i don't recommend to do it this way. You can use openOCD to donwload the image instead.

Thanks for the reply!
I will try both ways to download the bbl. So if I use pitonstream, I understand that you used the Linux Bootrom without loading from SD. So did you set uart_boot_en to 0 (if it's 1 then baremetal bootrom is used) or did you just change the verilog code to always use the Linux Bootrom and keep the uart_boot_en =1 ?