Add Waveshare ESP32-S3-Touch-LCD-4

[maxulm]

Could you please add ESP32-S3-Touch-LCD-4?
https://www.waveshare.com/wiki/ESP32-S3-Touch-LCD-4

Regards Max

[fvanroie]

I don't own this new device, maybe some other user can create and share their configuration for this new display.

[maxulm]

This would be great! Just tell me, if I can support.

[ahb-bs]

Hi - I've just received the Waveshare ESP32-S3-Touch-LCD-5B and it's screen is just what I'm looking for - high density, wide viewing angles.

But I can seem to get it to work with Openhasp and I've tried a few different variations. It seems to running the ST7262 but struggling to get the screen working (I can connect to the wifi of the device, just a blank screen). Can anyone help with this one too as it would be my dream device for around the home!

[fvanroie]

You need a driver for the CH422G IO-expander. TP_RST,LCD_RST and DISP pins are controlled by the expander.
Maybe try to get the display working in a minimal sketch first before porting the functionality into openHASP.

[ahb-bs]

Hi - thanks. I've the demo's that come with the device so I've a bin file and code, but never had any success configuring openhasp and compiling the code.

;***************************************************;
;   Waveshare ESP32-S3-Touch-LCD-5.0                ;
;               - 16-bit RGB TFT                    ;
;               - GT911 touch controller            ;
;***************************************************;

[env:esp32-s3-touch-lcd-5]
platform = espressif32
board = esp32s3
framework = arduino
monitor_speed = 115200

; Custom settings for the ESP32-S3 Touch LCD 5
build_flags =
    ${arduino_esp32s3_v2.build_flags}
    ${esp32s3.ps_ram}
    ;-DARDUINO_USB_CDC_ON_BOOT
	;-DUSE_USB_CDC_CONSOLE
    -D HASP_USE_ARDUINOGFX=1
    -D HASP_LV_USE_SW_ROTATE=1
    -D CONFIG_ESP_PANEL_USE_1024_600_LCD=1
    -D CONFIG_I2C_MASTER_SCL_IO=9
    -D CONFIG_I2C_MASTER_SDA_IO=8
    -D CONFIG_I2C_MASTER_NUM=I2C_NUM_0
    -D CONFIG_ESP_PANEL_CHECK_RESULT_ASSERT=0
    -D CONFIG_ESP_PANEL_ENABLE_LOG=0
    -D LV_VDB_SIZE=76800 ; 10% of full framebuffer
    -D TFT_WIDTH=1024
    -D TFT_HEIGHT=600
    -D TFT_DE=5
    -D TFT_VSYNC=3
    -D TFT_HSYNC=46
    -D TFT_PCLK=7
    -D TFT_B0=14
    -D TFT_B1=38
    -D TFT_B2=18
    -D TFT_B3=17
    -D TFT_B4=10   
    -D TFT_G0=39
    -D TFT_G1=0
    -D TFT_G2=45
    -D TFT_G3=48
    -D TFT_G4=47
    -D TFT_G5=21
    -D TFT_R0=1
    -D TFT_R1=2
    -D TFT_R2=42
    -D TFT_R3=41
    -D TFT_R4=40
    -D TFT_BCKL=6 ; use GPIO06 as backlight PIN
    ; Panel Settings
    -D TFT_HSYNC_POLARITY=0
    -D TFT_HSYNC_FRONT_PORCH=20   ; Maximum HSYNC Front Porch
    -D TFT_HSYNC_PULSE_WIDTH=10    ; Typical HSYNC Pulse Width
    -D TFT_HSYNC_BACK_PORCH=10    ; Typical HSYNC Back Porch
    -D TFT_VSYNC_POLARITY=0
    -D TFT_VSYNC_FRONT_PORCH=10   ; Maximum VSYNC Front Porch
    -D TFT_VSYNC_PULSE_WIDTH=10   ; Typical VSYNC Pulse Width
    -D TFT_VSYNC_BACK_PORCH=10   ; Typical VSYNC Back Porch
    -D TFT_PCLK_ACTIVE_NEG=0
    -D TFT_PREFER_SPEED=14000000  ; 1/2 of Typical DCLK Frequency
    -D TFT_AUTO_FLUSH=1
    ; Touch Settings
    -D TOUCH_WIDTH=1024
    -D TOUCH_HEIGHT=600
    -D TOUCH_DRIVER=0x911
    -D TOUCH_SCL=9
    -D TOUCH_SDA=8
    -D TOUCH_IRQ=-1
    -D TOUCH_RST=-1
    -D I2C_TOUCH_ADDRESS=0x5d ; or 0x5D
    -D I2C_TOUCH_FREQUENCY=400000
    -D BACKLIGHT_FREQUENCY=1000 ;adopted frerquency for MP3302DJ-LF-Z (200 to 1000Hz) ->higher is better for sound!

lib_deps =
    ${arduino_esp32s3_v2.lib_deps}
    ${arduinogfx.lib_deps}
    Arduino_RPi_DPI_RGBPanel_mod
    ${goodix.lib_deps}
    ${sunton-esp32-s3-tft.lib_deps}

[ahb-bs]

I think I'm getting close, but there is a flicker/wobble that I can't seem to get rid of.

;***************************************************;
;   Waveshare ESP32-S3-Touch-LCD-5                  ;
;               - 16-bit RGB TFT                    ;
;               - GT911 touch controller            ;
;***************************************************;

[ws_esp32_s3_touch]
extends = arduino_esp32s3_v2, flash_8mb
board = esp32-s3-devkitc-1
board_build.arduino.memory_type = qio_opi

;region -- ArduinoGFX build options ------------------------
    -D HASP_USE_ARDUINOGFX=1
    -D HASP_LV_USE_SW_ROTATE=1
;endregion
 
lib_deps =
    ${arduino_esp32s3_v2.lib_deps}
    Arduino_RPi_DPI_RGBPanel_mod
    ${arduinogfx.lib_deps}
    ${goodix.lib_deps}

[env:ws_esp32_s3_touch_lcd_4p3]
extends = ws_esp32_s3_touch

build_flags =
    -D HASP_MODEL="Waveshare ESP32-S3-Touch-LCD-5"
    ${arduino_esp32s3_v2.build_flags}
    ${esp32s3.ps_ram}
    ;-DARDUINO_USB_CDC_ON_BOOT
	;-DUSE_USB_CDC_CONSOLE
    -D HASP_USE_ARDUINOGFX=1
    -D HASP_LV_USE_SW_ROTATE=1
    -D CONFIG_ESP_PANEL_USE_1024_600_LCD=1
    -D CONFIG_I2C_MASTER_SCL_IO=9
    -D CONFIG_I2C_MASTER_SDA_IO=8
    -D CONFIG_I2C_MASTER_NUM=I2C_NUM_0
    -D CONFIG_I2C_MASTER_FREQ_HZ=400000
    -D CONFIG_ESP_PANEL_CHECK_RESULT_ASSERT=0
    -D CONFIG_ESP_PANEL_ENABLE_LOG=0
    -D ESP_PANEL_LCD_BUS_SKIP_INIT_HOST=1
    -D ESP_PANEL_TOUCH_BUS_SKIP_INIT_HOST=1    
    -D TFT_DATA_WIDTH=16 
    -D LV_VDB_SIZE=153600 ; 10% of full framebuffer
    -D TFT_WIDTH=1024
    -D TFT_HEIGHT=600
    -D TFT_DE=5
    -D TFT_VSYNC=3
    -D TFT_HSYNC=46
    -D TFT_PCLK=7
    -D TFT_B0=14
    -D TFT_B1=38
    -D TFT_B2=18
    -D TFT_B3=17
    -D TFT_B4=10   
    -D TFT_G0=39
    -D TFT_G1=0
    -D TFT_G2=45
    -D TFT_G3=48
    -D TFT_G4=47
    -D TFT_G5=21
    -D TFT_R0=1
    -D TFT_R1=2
    -D TFT_R2=42
    -D TFT_R3=41
    -D TFT_R4=40
    -D TFT_BCKL=6 ; use GPIO06 as backlight PIN
    ; Panel Settings
    -D TFT_HSYNC_PULSE_WIDTH=88
    -D TFT_HSYNC_BACK_PORCH=196
    -D TFT_HSYNC_FRONT_PORCH=56
    -D TFT_VSYNC_PULSE_WIDTH=6
    -D TFT_VSYNC_BACK_PORCH=20
    -D TFT_VSYNC_FRONT_PORCH=8
    -D TFT_PCLK_ACTIVE_NEG=1
    -D TFT_HSYNC_POLARITY=0
    -D TFT_VSYNC_POLARITY=0
    -D TFT_PREFER_SPEED=13900000  ; 1/2 of Typical DCLK Frequency
    -D TFT_AUTO_FLUSH=1
    -D ESP_PANEL_LCD_RGB_FRAME_BUF_NUM=2    
    -D TFT_BOUNCE_BUFFER_SIZE=40480

    ; Touch Settings
    -D TOUCH_WIDTH=1024
    -D TOUCH_HEIGHT=600
    -D TOUCH_DRIVER=0x911
    -D TOUCH_SCL=9
    -D TOUCH_SDA=8
    -D TOUCH_IRQ=-1
    -D TOUCH_RST=-1
    -D I2C_TOUCH_ADDRESS=0x5d ; or 0x5D
    -D I2C_TOUCH_FREQUENCY=400000
    -D BACKLIGHT_FREQUENCY=20000

`

[ahb-bs]

I've settled on the following for the 5 inch

;***************************************************;
;   Waveshare ESP32-S3-Touch-LCD-5                  ;
;               - 16-bit RGB TFT                    ;
;               - GT911 touch controller            ;
;***************************************************;


[ws_esp32_s3_touch]
extends = arduino_esp32s3_v2, flash_16mb
board = esp32-s3-devkitc-1
board_build.arduino.memory_type = qio_opi

build_flags =
    ${arduino_esp32s3_v2.build_flags}
    ${esp32s3.ps_ram}

;region -- ArduinoGFX build options ------------------------
    -D HASP_USE_ARDUINOGFX=1
    -D HASP_LV_USE_SW_ROTATE=1
;endregion
 
lib_deps =
    ${arduino_esp32s3_v2.lib_deps}
    Arduino_RPi_DPI_RGBPanel_mod
    ${arduinogfx.lib_deps}
    ${goodix.lib_deps}

[env:ws_esp32_s3_touch_lcd_4p3]
extends = ws_esp32_s3_touch

build_flags =
    -D HASP_MODEL="Waveshare ESP32-S3-Touch-LCD-5"
    ${arduino_esp32s3_v2.build_flags}
    ${esp32s3.ps_ram}

;    -D CONFIG_LV_MEM_CUSTOM=y
 ;   -D CONFIG_LV_MEM_SIZE=32768  ; 64 KB LVGL memory in PSRAM    
 ;   -D CONFIG_SPIRAM_ALLOW_STACK_EXTERNAL_MEMORY=y
 ;   -D CONFIG_SPIRAM_STACK_SIZE=10240  ; Example stack size in bytes
 ;   -D CONFIG_COMPILER_OPTIMIZATION_PERF=y
 ;   -D CONFIG_SPIRAM_USE_MALLOC=y
 ;   -D CONFIG_SPIRAM_MALLOC_ALWAYSUSE=y
 ;   -D CONFIG_SPIRAM_HEAP_RESERVE=524288  ; Reserve 512 KB for heap

    ;-DARDUINO_USB_CDC_ON_BOOT
	;-DUSE_USB_CDC_CONSOLE
    -D HASP_USE_ARDUINOGFX=1
    -D HASP_LV_USE_SW_ROTATE=1
    -D CONFIG_ESP_PANEL_USE_1024_600_LCD=1
    -D CONFIG_I2C_MASTER_SCL_IO=9
    -D CONFIG_I2C_MASTER_SDA_IO=8
    -D CONFIG_I2C_MASTER_NUM=I2C_NUM_0
    -D CONFIG_I2C_MASTER_FREQ_HZ=400000
    -D CONFIG_ESP_PANEL_CHECK_RESULT_ASSERT=0
    -D CONFIG_ESP_PANEL_ENABLE_LOG=0
    -D ESP_PANEL_LCD_BUS_SKIP_INIT_HOST=1
    -D ESP_PANEL_TOUCH_BUS_SKIP_INIT_HOST=1    
    -D TFT_DATA_WIDTH=16 
    -D LV_VDB_SIZE=90000
    -D TFT_WIDTH=1024
    -D TFT_HEIGHT=600
    -D TFT_DE=5
    -D TFT_VSYNC=3
    -D TFT_HSYNC=46
    -D TFT_PCLK=7
    -D TFT_B0=14
    -D TFT_B1=38
    -D TFT_B2=18
    -D TFT_B3=17
    -D TFT_B4=10   
    -D TFT_G0=39
    -D TFT_G1=0
    -D TFT_G2=45
    -D TFT_G3=48
    -D TFT_G4=47
    -D TFT_G5=21
    -D TFT_R0=1
    -D TFT_R1=2
    -D TFT_R2=42
    -D TFT_R3=41
    -D TFT_R4=40
    -D TFT_BCKL=6 ; use GPIO06 as backlight PIN

   ; Panel Settings
    -D TFT_HSYNC_POLARITY=0
    -D TFT_HSYNC_FRONT_PORCH=36   ; Maximum HSYNC Front Porch
    -D TFT_HSYNC_PULSE_WIDTH=6    ; Typical HSYNC Pulse Width
    -D TFT_HSYNC_BACK_PORCH=36    ; Typical HSYNC Back Porch
    -D TFT_VSYNC_POLARITY=0
    -D TFT_VSYNC_FRONT_PORCH=8   ; Maximum VSYNC Front Porch
    -D TFT_VSYNC_PULSE_WIDTH=6   ; Typical VSYNC Pulse Width
    -D TFT_VSYNC_BACK_PORCH=8  ; Typical VSYNC Back Porch
    -D TFT_PCLK_ACTIVE_NEG=1
    -D TFT_PREFER_SPEED=14000000  ; 1/2 of Typical DCLK Frequency
    -D TFT_AUTO_FLUSH=1

    ; Panel Settings
;    -D TFT_HSYNC_POLARITY=0
;    -D TFT_HSYNC_FRONT_PORCH=56
;    -D TFT_HSYNC_PULSE_WIDTH=88
;    -D TFT_HSYNC_BACK_PORCH=196
;    -D TFT_VSYNC_POLARITY=0
;    -D TFT_VSYNC_FRONT_PORCH=8
;    -D TFT_VSYNC_PULSE_WIDTH=6
;    -D TFT_VSYNC_BACK_PORCH=20

;    -D TFT_PCLK_ACTIVE_NEG=1
;    -D TFT_PREFER_SPEED=13900000  ; 1/2 of Typical DCLK Frequency
;    -D TFT_AUTO_FLUSH=1

;    -D ESP_PANEL_LCD_RGB_FRAME_BUF_NUM=3 
;    -D TFT_BOUNCE_BUFFER_SIZE=20480

    ; Touch Settings
    -D TOUCH_WIDTH=1024
    -D TOUCH_HEIGHT=600
    -D TOUCH_DRIVER=0x911
    -D TOUCH_SCL=9
    -D TOUCH_SDA=8
    -D TOUCH_IRQ=-1
    -D TOUCH_RST=-1
    -D I2C_TOUCH_ADDRESS=0x5d ; or 0x5D
    -D I2C_TOUCH_FREQUENCY=400000
    -D BACKLIGHT_FREQUENCY=20000
    
lib_deps =
    ${sunton-esp32-s3-tft.lib_deps}
    ${goodix.lib_deps}    
`

[tomasinouk]

Hi, any chance you could share the flash file? I have the same display and mildly put it not up to task to build OpenHASP myself.
Thank you

[j0yze]

Glad to see that someone else has the ESP32-S3-Touch-LCD-5.
Is there a documentation, of how to connect and flash this board? I am completely new with openHASP.

[Maliron]

So the above would work for the LCD-5, I have the demo code for the LCD-4, and I am pretty sure I can get the build options for the LCD-4 from there. I'm very new to openHASP, so I assume I just need to add the build options to the top the openHASP code before compiling and flashing?

[fvanroie]

Please test if this configuration and bin file works properly and let me know.

Can someone please add these devices to the OpenHASP docs repo?

[Maliron]

I don't see a bin and config for the ESP32-S3-Touch-LCD-4 that this thread was started for. I tried the 4p3 (accidentally) and it did not work for the 480x480 ESP32-S3-Touch-LCD-4. Has anyone gotten this working yet? If you can point me at the OpenHASP doc you want these added to I can give it a crack at adding them.