Is there support for TL series fans and controller?

[bonkas]

Is there support for TL series fans and controller?

I have these in my system and can provide any troubleshooting required to make this work.

[bcarvalho2500]

@bonkas Are you on Linux? I have a fork of this repo where I can add your product id and fan specs to see if that works.

[bonkas]

@bcarvalho2500 Yes I dual boot this system with Windows and PopOS.

This is what is reported from Windows:

[bcarvalho2500]

@bonkas Huh that has a VID I was not expecting. Can you try running lsusb -v | grep -i 0cf2 on PopOS and see if that returns anything? If that doesn't return anything can you try lsusb -v | grep -i lianli

[bonkas]

@bcarvalho2500 I certainly can, Just at work atm but can do in ~6 hours time :P.

I will edit this message once I have more information.

EDIT:

Okay the first and second command did not return anything.

Dumping a complete list I found this device which you may be interested in (I also attached the complete dump of lsusb -v)
USBDeviceDump.txt
:

Bus 001 Device 005: ID 0416:7372 Winbond Electronics Corp. TL_Series_ControllerV0.58
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0416 Winbond Electronics Corp.
idProduct 0x7372
bcdDevice 1.01
iManufacturer 0
iProduct 2 TL_Series_ControllerV0.58
iSerial 1 Nuvoton
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x004b
bNumInterfaces 3
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 63
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 32
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.10
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled

[bcarvalho2500]

@bonkas Alright I think I may have something that will work. Just for my piece of mind there are somethings in the original code that I don't exactly understand so I copied the lines for the 'SLI' fans which are relatively new also. How the whole program works is that it just edits the files on start so if it doesn't work and uninstall and reboot should do the trick.

If you wanna go ahead and try it out you can clone it with this: git clone -b feature/add_support_for_tl_fans --single-branch https://github.com/bcarvalho2500/uni-sync.git

Please let me know how it works!

[bonkas]

hmm I am still having no luck, I am thinking it is a "me" problem though.

I have been uninstalling, installing, rebooting over and over a number of times now but I am not getting the config file to populate except for ONCE it populated (I will paste contents below) I noticed the RGB dissapeared from the fans so something must have communicated with the fans so I tried to increase the fan speed to 100% and restart the service but nothing happened. I havent been able to repeat the config file being created since.

I have tried installing as my regular user and using sudo to no avail, the config file is either not created or is created as an empty json in the folder containing the application. The path given in the github doesnt seem to exist either, well I can see it but cannot do anything with it... not sure what is going on here.

Is this something you can offer some assistance with?

This is the config I managed to generate ONE time only.

{
"configs": [
{
"device_id": "VID:1046/PID:29554/SN:Nuvoton",
"sync_rgb": false,
"channels": [
{
"mode": "Manual",
"speed": 100
},
{
"mode": "Manual",
"speed": 100
},
{
"mode": "Manual",
"speed": 100
},
{
"mode": "Manual",
"speed": 100
}
]
}
]
}

[bonkas]

Welp! Rebooting into windows gives me device not recognised and the L-Connect software can no longer see the controller.

The fans are stuck at full speed now with no active RGB activity either, I now have an added 8-10s boot time at BIOS with a flashing cursor... uh-oh.

EDIT:

After a full power down of the system and reboot it now seems to be booting normally and I have RGB activity, uninstalled and reinstalled device drivers and now the error is gone and the l-connect software can see the controller again.. whew.

Tried again and as soon as the app service starts the controller goes wonky again, I guess something is not right here.

[bcarvalho2500]

@bonkas So the empty json is created when you install but when the application first runs, that's when the json is filled with default values and once the json is filled out, it's never created again. So if I read what you said correctly, that should be normal behavior.

I'll need to take a look more into how to write to HID devices to try and see why yours didn't work. Your fans vendor id was different from all the others so maybe something changed there? I'll try to learn how to get report data but may need you to provide it since you have a working L-connect with those fans.

Sorry I couldn't get it to work sooner.

[bonkas]

Yup, happy to help further but am a bit out of my depth here.

I have tried to include as much information as possible about what I noticed to try narrow down the issue but it seems the controller gets communicated with and then freaks out, only a hard reset of the device and then subsequent drive removal/reinstall in windows resolves this.

[mega-watt]

Hello,

I want to add to this issue to hopefully help.
The newer TL hubs seem to have somethings that is above the controller.

lsusb output:

Bus 003 Device 005: ID 0416:7372 Winbond Electronics Corp. TL_Series_ControllerV0.58
Bus 003 Device 003: ID 1a40:0801 Terminus Technology Inc. USB 2.0 Hub

lsusb -t output:

/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
|__ Port 6: Dev 3, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 3: Dev 5, If 0, Class=Vendor Specific Class, Driver=, 12M
|__ Port 3: Dev 5, If 1, Class=Human Interface Device, Driver=usbhid, 12M
|__ Port 3: Dev 5, If 2, Class=Human Interface Device, Driver=usbhid, 12M

Looking forward to seeing this support the TL line.

Regards.

[YamiYukiSenpai]

Any changes since?

[scandinave]

For me there is :

Bus 003 Device 005: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub // Uni Fan USB Hub from Lian Li edge Gold
Bus 003 Device 006: ID 0416:8041 Winbond Electronics Corp. SLV3RX_V1.6 // triple pack wireless TL reverse ???
Bus 003 Device 008: ID 1a86:8091 QinHeng Electronics USB HUB
Bus 003 Device 009: ID 0416:8040 Winbond Electronics Corp. SLV3TX_V1.6 // Triple pack wireless TL ???
Bus 003 Device 011: ID 0416:7398 Winbond Electronics Corp. HydroShift LCD v0.7 // Hydroshift pump
Bus 003 Device 012: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3 // Solo pack wireless LCD
Bus 003 Device 013: ID 1a86:8091 QinHeng Electronics USB HUB
Bus 003 Device 014: ID 1a86:2107 QinHeng Electronics SLV3H // dont know ???
Bus 003 Device 015: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3 // Triple pack wireless LCD
Bus 003 Device 016: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3
Bus 003 Device 017: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3

I have a set-up with 3 wireless TL at top on aio, 3 wireless TL reverse at bottom, 1 wireless TL LCD at rear, 3 wireless TL reverse LCD at side and hydroshift AIO pump

[ItsLiyua]

I'd be interested in this as well. Let me know if I can provide some data or test some code.

[bonkas]

@bcarvalho2500 Is there anything we can do to help progress this? It seems there are many wanting this, it doesnt look like any one else is working on this solution for TL fans.

Please let me know what I can do to help. I do have some coding experience but I am a hardware guy, also a linux beginner.

[phstudy]

For me there is :

Bus 003 Device 005: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub // Uni Fan USB Hub from Lian Li edge Gold
Bus 003 Device 006: ID 0416:8041 Winbond Electronics Corp. SLV3RX_V1.6 // triple pack wireless TL reverse ???
Bus 003 Device 008: ID 1a86:8091 QinHeng Electronics USB HUB
Bus 003 Device 009: ID 0416:8040 Winbond Electronics Corp. SLV3TX_V1.6 // Triple pack wireless TL ???
Bus 003 Device 011: ID 0416:7398 Winbond Electronics Corp. HydroShift LCD v0.7 // Hydroshift pump
Bus 003 Device 012: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3 // Solo pack wireless LCD
Bus 003 Device 013: ID 1a86:8091 QinHeng Electronics USB HUB
Bus 003 Device 014: ID 1a86:2107 QinHeng Electronics SLV3H // dont know ???
Bus 003 Device 015: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3 // Triple pack wireless LCD
Bus 003 Device 016: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3
Bus 003 Device 017: ID 1cbe:0006 Luminary Micro Inc. TL-LCD Wireless-1.3

I have a set-up with 3 wireless TL at top on aio, 3 wireless TL reverse at bottom, 1 wireless TL LCD at rear, 3 wireless TL reverse LCD at side and hydroshift AIO pump

I recently purchased the Wireless TL series as well, and I can confirm the following:

0416:8040 Winbond Electronics Corp. SLV3TX_V1.6 // RF Transmitter  
0416:8041 Winbond Electronics Corp. SLV3RX_V1.6 // RF Receiver  

I’ll probably try looking into how the Wireless TL version works and see if it’s possible to implement support for it. I’ll share anything useful I find!